INJECTION MOLDING ENCYCLOPEDIA
Injection Molding Encyclopedia
Find hot runner articles by industry, material, and molding defect.
Frequently Asked Questions
Find products by material
View all four productsTotal 194 articles · Current:All industries
Browse by defect, material, and industry
194 articles
When Is PEEK Justified for Consumer Electronics Components?
PEEK (Victrex 650G):, melting point 343°C, nozzle 395°C, barrel zones 375/380–385/390°C, mold temperature 170–200°C, drying 120–150°C for 3–5 hours, barrel heating capacity 400°C; HT/ST requires 430°C). The only rule: Use PEEK only if no other material can meet the part's core requirement.
PEEK Compressor Seals Leaking After Three Years: Why?
PEEK (Victrex 650G): Melting point 343°C, nozzle 395°C, barrel zones 375/380–385/390°C, mold temp 170–200°C, drying 120–150°C × 3–5h, unreinforced shrinkage 0.most/1.3%, 30% GF 0.30%/0.most. Failure often stems from 'creep' or displacement; root cause is failing to calculate clearances separately for hot and cold states.
Switching Surgical Instruments from Metal to PEEK: What Do You Gain?
PEEK (Victrex 650G): Melting point 343°C, nozzle 395°C, barrel zones 375/380–385/390°C, mold temp 170–200°C, drying 120–150°C × 3–5h, barrel capacity 400°C, unreinforced shrinkage 0.most/1.3%. Benefits include weight reduction, imaging compatibility, insulation, and sterilization resistance, traded against stiffness and cost.
Why Does the LCP Warp in 0 4mm Pitch Board-to-Board Connectors?
LCP (Vectra E130i, 30% GF): Melt temp 335°C, hot runner 335–345°C, mold temp 80–120°C, shrinkage 0.10%/0.40% (4x anisotropy). Rapid solidification limits packing effectiveness. Balance directional differences using gate location and zoned mold temperatures; avoid extending packing time.
Replacing LCP with PA9T in Board-to-Board Connectors: Three Critical Requirements
PA9T (Genestar G1350A, 35% GF): Melting point 300°C, Tg 125°C, moisture absorption 0.19%, shrinkage 0.3%/0.9% (3x anisotropy), drying 70–90°C for 4–8 hours. Success depends on three prerequisites: complete filling at fine pitches, coplanarity tolerance, and effective moisture control.
PPS for Board-to-Board: Stable Dimensions, but Low Insertion Resistance?
PPS (DURAFIDE 1140A1, 40% GF): Mold temp 150°C, max material temp 360°C, nozzle 310–320°C, shrinkage 0.3%/0.8%, pin gate φ0.8–1.2mm,, vent depth 0.005–0.008mm.. High modulus ensures dimensional stability but causes stress concentration on terminals and hole walls during insertion due to lack of part deflection.
PA46 for Board-to-Board: Why Must Melt Temp Exceed Melting Point by >10°C?
PA46 (Stanyl TS250F6D, 30% GF): Melting point 295°C, melt temp must be >305°C (optimal 305–320°C), barrel/nozzle 305–320°C, shrinkage 0.4%/1.1%. Below 305°C, 0.2–0.3mm thin walls suffer short shots and weak weld lines; this is a temperature issue, not pressure.
LCP Wire-to-Board Connectors: Why Thick Walls Fail and Thin Walls Succeed
LCP (Vectra E130i, 30% GF): Melting point 335°C, hot runner 335–345°C, mold temperature 80–120°C, shrinkage 0.10%/0.40%. Rapid solidification seals packing channels in thick walls, while thin-wall sections fall below flow limits. These opposing defects require separate solutions.
Moisture Impact on PA9T Locking Clips in Wire-to-Board Connectors
PA9T (Genestar G1350A, 35% GF): Water absorption 0.19% (ISO 62), drying 70–90°C × 4–8h, moisture ≤0.20%, notched impact 12kJ/m². Moisture absorption in thin clip sections changes protrusion height and root clearance simultaneously, causing tight mating and reduced rebound space.
PPS Locking Clips in Wire-to-Board Connectors: Brittle Failure Analysis
PPS (DURAFIDE 1140A1, 40% GF): Mold temp 150°C, max material temp 360°C, nozzle 310–320°C, low notched impact strength. Clip fractures occur mostly at root corners (80%) and back of protrusions (20%). Address roots with R0.5 fillets and thickness gradients; adjust gate location to alter fiber orientation for protrusion issues.
Can't find the matching gate issue? Share material, part, and defect details. Our engineers will evaluate it by part.
Online selection and quote