MATERIAL TOPIC
PPS
PPS is often high-temperature and glass-filled; evaluate gate carbon buildup, wear, and residence time together.
19 articles
Articles in this topic
View all articlesMold Deposits: Persistent Residue on Mold Surfaces
After days of continuous production, brown or white residue forms on cavity surfaces, causing spots and haze on parts. This is mold buildup.
Causes of Color Variation: Melt Temperature, Residence Time, and Purge Residue
Color variation may appear as darker areas near the gate, yellowing at the far end of the same part, or batch-to-batch mismatches that require multiple shots to stabilize after a color change. Often dismissed as "material issues," it is critical to distinguish between uniform shifts across the entire mold and localized variations.
Scorching and Charring: Compressed Gas Causes Material Carbonization
Dark brown or black patches with halos at part ends or weld lines that cannot be cleaned and appear consistently, caused by compressed gas heating the melt to carbonization temperatures.
Black Specks: Melt Carbonization, Residence Time, and Dead Zone Residue
Dark spots (0.x–1.x mm) on or below the surface that cannot be polished; these may appear in fixed or random locations. Often mistaken for dirt, but they persist even with new resin, indicating residue in the hot runner or screw.
Flash Causes: Parting Line, Clamping Force, and Cavity Pressure
Flash is indicated by thin fins along edges or hard flakes surrounding holes and ejector pins that resist trimming. This issue is common in thin-wall, multi-cavity parts and is directly linked to gate size and holding pressure settings.
Causes of Short Shots: Gate Temperature, Flow Length Ratio, and Incomplete Filling
Missing sections at the far ends or in thin walls indicate short shots (incomplete filling). Unlike clogged nozzles, which stop flow entirely, short shots occur when the melt halts mid-fill. Identify the root cause before troubleshooting.
Gate Wear and Corrosion: Increased Diameter Affects Break-off
After prolonged use, gate diameters exceed drawing specifications, making clean break-off difficult and causing streaks. Glass-filled or flame-retardant materials can also lead to internal pitting corrosion.
Gate Residue and Protrusion: Break-off Timing, Hole Size, and Valve Pin
Protrusions, residual rings, or shear marks at the gate lead to assembly fit issues and require trimming for cosmetic parts. This is known as gate residue.
Temperature Control Issues and Runaway: Thermocouples, Zones, and Power
Symptoms include consistent short shots or yellowing despite correct setpoints, or temperature fluctuations synchronized with mold opening and closing. These indicate circuit issues rather than simple offset errors.
Hot Runner Leakage: Joint Faces, Preload, and Fit Clearance
Resin rings appear on the mold face, and flash-like overflow consistently occurs at a single location. Inspection confirms leakage from the hot runner/manifold joint or gate bushing interface, not the cavity.
Valve Pin Sticking and Poor Closure: Drive, Timing, and Gate Fit
Two common issues in valve-gate hot runners are: residual material or stringing at specific gates due to poor closure, and delayed actuation causing fill sequence variations or short shots due to sticking.
Gate Freezing and Cold Material: Temperature, Cycle Wait Time, and Shutdown Residue
Sudden short shots or reduced output signal gate freezing; dark hard marks after restart indicate cold material. Both issues originate at the nozzle tip but stem from different causes.
Gate Carbonization: Black-Brown Layers and Specks
Black specks and inconsistent flow indicate a hard, brittle black-brown layer forming inside the gate. Carbonization accumulates gradually as material coats the gate wall and degrades under repeated heating cycles.
Causes of Excessive Saliva: Film Formation, Dripping, and Sealing from Pack Pressure
When injection ends and the screw retracts, a small film or drip of material escapes through the gate, sticking to the part or dripping onto the mold. This excess material forms a thin sheet that is hard to remove and can damage subsequent parts during molding.
Gate Stringing Causes: Gate Temperature, Valve Pin Timing, and Solutions
When the mold opens, a thin, hair-like string pulls from the gate. If left untreated, it causes shorts on adjacent pins, damages mold surfaces, and falling debris contaminates the cavity.
Gate Defects in High-Temperature Molding: Why Machine Settings Provide Only Partial Relief
In LCP, PA6T, PA9T, and PPS molding, common gate defects include stringing, drooling, and nozzle clogging. While shops typically adjust temperature, injection speed, and packing time, improvements are often short-lived. The root cause lies not just in parameters: a constant-temperature hot runner must compromise across all three stages of the molding cycle.
Stringing, Drooling, and Clogging: Differences, Causes, and Solutions
In high-temperature molding, stringing, drooling, and clogging are often grouped as gate defects, but their symptoms, causes, and adjustments differ. Changing a single parameter without first identifying the defect type may resolve one issue while worsening another.
FHFC vs. Standard Hot Runner: Comparing Cost Differences
An FHFC hot runner system requires a higher initial investment than a conventional constant-temperature system, but the cost difference cannot be expressed as a single number. The decision requires evaluating both the added cost and measurable returns. This article outlines the cost structure, benefit sources, and evaluation method; it does not replace a project quote.
Why Constant-Temperature Hot Runners Cause Stringing, Drooling, and Clogging
Stringing, drooling, and clogging may appear to be machine-setting issues, but a constant-temperature gate remains molten throughout the entire cycle. This article explains how each defect forms, how FHFC freezes the gate before opening, and why lowering the temperature or shortening the packing time only addresses symptoms.
Can't find the matching defect? Share photos of the resin, shot weight, and gate for a review against the actual structure.
Online selection and quote