INJECTION MOLDING ENCYCLOPEDIA
Injection Molding Encyclopedia
Find hot runner articles by industry, material, and molding defect.
Frequently Asked Questions
Find products by material
View all four productsTotal 194 articles · Current:All industries
Browse by defect, material, and industry
194 articles
Multi-Cavity Mold Temperature Variance: Why Center is Cold and Edges Hot?
Half of the multi-cavity temperature variance comes from water line flow distribution, and half from heat dissipation conditions of hot runner nozzles. Three measurement methods: infrared rough estimation, embedded thermocouple verification, and in-mold sensors for precision parts. Recommended hot runner zoning is 4–8 zones, divided by cavity position rather than a single zone for the whole mold.
Gate Stringing and Drooling: Why Is Adjustment So Difficult?
Stringing and drooling occur when the nozzle tip temperature is too high; clogging occurs when it is too low. All three issues happen at the interface between the hot nozzle tip and the mold gate. The SD Series seals with a cold slug, while the VG Series uses a valve pin—troubleshooting steps differ. LCP window: 335–345°C; PA46: 305–320°C. Materials with narrow processing windows are the most difficult to adjust.
How Thin Can Walls Be Before Short Shots Occur?
Flow ratio = flow length ÷ wall thickness; halving wall thickness doubles the flow ratio. LCP can fill walls as thin as 0.2mm.. For PA9T/PA46, watch out when the flow ratio approaches 75 at a 0.4 mm wall thickness. PPS with 40% GF requires margin. Three conditions for thin-wall molding: high injection speed, mold temperature raised by 10–20°C, and sufficient material temperature; the mold must have large gates, effective venting, and flat ejection.
Persistent Sink Marks in Thick Areas Despite Increased Packing Pressure
Sink marks occur because the gate freezes first, preventing packing pressure from reaching thicker sections that solidify later. Risk is high if wall thickness ratio exceeds 2:1; inevitable at 3:1. Four countermeasures ranked by effectiveness: place gate near thick area, increase mold temperature, local heating, extend packing time. Structural changes: hollow out, gradual transition, move to non-appearance surface, or split part.
Why Cycle Time Increases More Than Expected When Wall Thickness Grows?
Cooling time is proportional to the square of wall thickness: doubling wall thickness roughly quadruples cooling time. Crystalline materials have smaller coefficients but require accounting for crystallization exotherm. Water lines have the biggest impact (distance 2–3x hole diameter, no dead zones, inlet/outlet temp difference), followed by mold temperature, then material. Calculate cooling based on center temperature for thick walls; thin walls challenge filling and temperature control.
Why LCP is Preferred for Millimeter-Wave Radar Covers Even at 0.6mm Thickness?
At 76–81GHz,, thinner walls reduce loss; LCP's low viscosity enables filling 0.6mm-thick walls. With 30% GF, shrinkage is 0.10%/0.40%, with a 4x directional difference; part geometry must align with flow direction. Melting point: 335°C; low moisture absorption and minimal dimensional shift under thermal cycling. Gates and ejector pins must not be located within the radar main lobe area; coating thickness must be controlled.
Black Spots in Micro Parts: Linked to Machine Runtime, Not Material
PA46 (Stanyl TS250F6D, 30% GF): Melting point 295°C, optimal melt 305–320°C, barrel and nozzle 305–320°C. In micro parts with small shot sizes, residence time effects are amplified; black spots result from carbonization due to stagnation. Reducing runner volume and shortening cleaning cycles is more effective than adjusting temperature.
Why Choose PEEK for Micro Connectors?
PEEK (Victrex 650G):: melting point 343°C, long-term service temp ~250°C depending on grade; nozzle 395°C, mold temp 170–200°C, barrel requires 400°C). Three reasons to use PEEK in micro parts: multiple reflow passes, specific chemical resistance, and long-term exposure above 150°C. The trade-off is cost and yield rate.
Gate Stringing Causes: Gate Temperature, Valve Pin Timing, and Solutions
When the mold opens, a thin, hair-like string pulls from the gate. If left untreated, it causes shorts on adjacent pins, damages mold surfaces, and falling debris contaminates the cavity.
Causes of Excessive Saliva: Film Formation, Dripping, and Sealing from Pack Pressure
When injection ends and the screw retracts, a small film or drip of material escapes through the gate, sticking to the part or dripping onto the mold. This excess material forms a thin sheet that is hard to remove and can damage subsequent parts during molding.
Can't find the matching gate issue? Share material, part, and defect details. Our engineers will evaluate it by part.
Online selection and quote