INJECTION MOLDING ENCYCLOPEDIA
Injection Molding Encyclopedia
Find hot runner articles by industry, material, and molding defect.
Frequently Asked Questions
Find products by material
View all four productsTotal 194 articles · Current:All industries
Browse by defect, material, and industry
194 articles
How FHFC Hot Runner Gate Temperature Control Works
FHFC hot runners are often assumed to heat and cool the entire system continuously, raising concerns about energy use and response speed. In practice, only the gate area changes temperature; the manifold and runners remain at a constant temperature. This article explains stage-based control logic, energy scope, and structural boundaries.
Gate Defects in High-Temperature Molding: Why Machine Settings Provide Only Partial Relief
In LCP, PA6T, PA9T, and PPS molding, common gate defects include stringing, drooling, and nozzle clogging. While shops typically adjust temperature, injection speed, and packing time, improvements are often short-lived. The root cause lies not just in parameters: a constant-temperature hot runner must compromise across all three stages of the molding cycle.
Why Constant-Temperature Hot Runners Cause Stringing, Drooling, and Clogging
Stringing, drooling, and clogging may appear to be machine-setting issues, but a constant-temperature gate remains molten throughout the entire cycle. This article explains how each defect forms, how FHFC freezes the gate before opening, and why lowering the temperature or shortening the packing time only addresses symptoms.
Why LCP Gates Are Highly Susceptible to Defects
LCP is difficult to mold not because of machine setup challenges, but because the gate operates between high temperatures and thermal degradation. High processing temperatures, low melt viscosity, thermal sensitivity, and tight precision connector requirements combine to cause stringing, drooling, and clogging. This article explains the four root causes and how dynamic gate temperature control optimizes timing.
FHFC Hot Runner vs. Mold Fast Heat, Fast Cool: What's the Difference?
Though both share a name, their scope differs. Mold RHCM adjusts the entire cavity temperature to improve surface finish. In contrast, FHFC hot runners heat only the gate area to prevent stringing, drooling, and clogging. This article compares their operating range, equipment, cost, cycle impact, and selection criteria.
Why We Recommend the SD Series and When to Use a Valve Gate
For precision connector production, an SD Series nozzle paired with dynamic gate temperature control is typically the first choice. Valve Gate systems remain essential for demanding gate aesthetics, surface gating, independent multi-cavity control, and specific materials. This article outlines the four nozzle types and the recommended selection order.
FHFC Hot Runner: Cost Savings and Yield Improvement for Factories
FHFC benefits extend beyond gate appearance to four production cost drivers: yield, downtime, labor, and consumables. This article quantifies the hidden costs of constant-temperature solutions, breaks down full-cycle expenses using precision connector mass-production cases, identifies unsuitable scenarios and common misconceptions, and explains why procurement quotes often diverge from total cost of ownership.
Core Principles and Technical Comparison: Constant-Temp vs. FHFC Hot Runners
Constant-temperature hot runners maintain uniform high heat throughout the cycle, relying on material flowability and gate structure to manage defects. FHFC heats before filling and cools before sealing, trading gate temperature timing for a wider molding window. This article compares control logic, operational advantages, and material compatibility to guide your selection decision.
Ultimate Hot Runner Selection Guide: Constant Temp vs. FHFC (Factory Comparison)
This final guide translates prior comparisons into actionable selection criteria: first evaluate material heat resistance and shear sensitivity, then product precision and cosmetic requirements, and finally batch size and cycle time. It includes decision tables for material types, precision levels, and mass production scenarios, while highlighting three common factory selection mistakes.
Why Is Mold RHCM Rarely Used Today Despite Its Past Popularity?
RHCM mold technology is not obsolete; it effectively addressed key challenges during the high-gloss cosmetic parts era. However, shifts in materials and market demands have amplified its limitations in energy efficiency, cycle time, maintenance, and application scope. This article reviews its peak applications, analyzes four key drawbacks, and clarifies how it differs from hot runner dynamic gate temperature control.
Can't find the matching gate issue? Share material, part, and defect details. Our engineers will evaluate it by part.
Online selection and quote