INJECTION MOLDING ENCYCLOPEDIA
Injection Molding Encyclopedia
Find hot runner articles by industry, material, and molding defect.
Frequently Asked Questions
Find products by material
View all four productsTotal 194 articles · Current:All industries
Browse by defect, material, and industry
194 articles
Why Start Using PEEK for Headphone Diaphragms and Wearables?
Diaphragms are 0.05–0.1mm thick. High viscosity of PEEK requires mold temps of 170–200°C and high injection speeds, often using film molding. Density ~1.3, moderate internal damping, good fatigue resistance. Wearables offer sweat/chemical resistance, but UV resistance depends on grade/coating; check extractables per customer standards. Processing requires nozzle capability at 395°C and barrel at 400°C.
Why do molds and screws wear out faster when processing high glass fiber materials?
Glass fiber hardness exceeds that of mold steel substrates, and gate flow velocity is highest, causing the fastest wear. Enlarged gates affect part weight and appearance. Five countermeasures: Select H13/S136 and heat treat to above HRC50, use nitriding or PVD, make gates as inserts, add radii to runners, and select wear-resistant screw/barrel types. Higher injection speed and melt temperature accelerate wear.
LCP Connector Nozzle Clogging: Gate Freezes First
LCP clogging occurs when the gate cools before the channel. E130i specs: melting point 335°C, mold temperature 80–120°C; a large nozzle-to-mold temperature difference causes rapid heat loss at the outlet. Provides a three-step diagnosis: measure temperature, check heaters and thermocouples, and verify gate dimensions. Identifies operations that accelerate clogging.
PA46 Stringing: Semi-Solid Layer Tear vs. LCP Behavior
PA46 stringing results from tearing of the semi-solid layer, unlike LCP's whole-segment drag-out. Stanyl TS250F6D (30%GF) specifications: melting point 295°C; melt temperature must exceed 305°C, with an optimal range of 305–320°C. Key steps include inspecting the break surface, verifying melt temperature, and implementing preemptive cut-off. Reducing mold temperature is ineffective for this issue.
PPS Nozzle Clogging: Carbonization vs. Insufficient Temperature
PPS clogs are often misidentified as carbonization but frequently result from insufficient temperature causing freezing at the tip. Manufacturer data indicates DURAFIDE viscosity does not rise significantly during prolonged residence, confirming hot runner suitability. Provides distinguishing features for both clog types and respective treatment sequences.
PEEK Stringing: Troubleshooting Tough Strings – Melt Temp or Mold Temp Issue?
Thick, tough, elongated PEEK strings indicate high outlet melt temperature and retained melt strength, pointing to melt temp and residence time issues. PEEK 650G specs: nozzle 395°C, mold temp 170–200°C, melting point 343°C, leaving only 52°C margin. Provides sequence: measure temp, inspect gate, reduce residence time.
PPS drooling: Material seeps after 10 minutes of downtime. How to maintain the 150°C mold temperature?
PPS material leaks after 10 minutes of stoppage at 150°C mold temperature due to residual fluidity at the nozzle tip. Use 1140A1 (40%GF) nozzle set to 310–320°C, with melt temperature not exceeding 360°C. This article covers cleaning wait times, sealing methods, and irreversible parameter settings.
PPS Stringing: Why does stringing persist after raising the mold temperature to 150°C?
PPS mold temperature is at 150°C, leaving little room for increase, yet stringing persists—indicating an incorrect approach. For DURAFIDE 1140A1 (40%GF), use nozzle temperatures of 310–320°C; melt temperature must not exceed 360°C. This article explains what to adjust when mold temperature reaches its limit and why PPS stringing signifies a "failure to break."
Why Is PEEK Increasingly Used in Medical Applications?
PEEK withstands 134°C steam, EO, and gamma irradiation; radiation resistance is a key strength. Medical parts require medical-grade resin and compliance documentation: biocompatibility, extractables, change control, batch traceability. Processing demands dedicated machines/materials without regrind, resulting in low material utilization. Nozzle 650G operates at 395°C, mold temp 170–200°C, and barrel >400°C.
Endoscope Tip Components: Why LCP Is Critical
Tip wall thickness is 0.3 mm with flow lengths of tens of millimeters; high flow ratios prevent conventional materials from filling. LCP's low viscosity makes it nearly mandatory. Shrinkage is 0.10%/0.40%, with a 4x directional difference; lens holes must align with the flow direction. Sterilization cycles cause surface haze and micro-cracks; validation requires cycle testing plus surface inspection. Adhesive chemical resistance needs separate verification.
Can't find the matching gate issue? Share material, part, and defect details. Our engineers will evaluate it by part.
Online selection and quote