INJECTION MOLDING ENCYCLOPEDIA
Injection Molding Encyclopedia
Find hot runner articles by industry, material, and molding defect.
Frequently Asked Questions
Find products by material
View all four productsTotal 194 articles · Current:All industries
Browse by defect, material, and industry
194 articles
Why Do Weld Lines Break More Easily as Glass Fiber Content Increases?
At weld lines, glass fibers face each other without overlapping, leaving only resin for strength. Higher fiber content makes weld lines relatively weaker than the bulk material. Four reinforcement methods: increase mold temperature, increase injection speed, improve venting, and position weld lines on ribs or thick-wall areas. Acceptance requires local sampling and overall inspection.
Why Do Long Parts Always Warp? What Does Glass Fiber Orientation Do?
Glass fibers align with the flow direction, causing low shrinkage along the flow and high shrinkage perpendicular to it. This directional difference causes warpage. End gates tend to cause bowing, center gates W-shape, and side gates twisting. Flip the part and mold again to distinguish orientation-induced warpage from temperature-difference warpage. Process adjustments can reduce this by 30–50%.
Why Use PA9T Instead of PA66 for Sensor Housings in the Engine Bay?
The engine bay experiences −40°C to 125°C plus humidity. PA66 has a melting point of 260°C, Tg of 60–70°C, and high water absorption, leading to thermal aging, creep, and insulation degradation over time. PA9T has a melting point of 300°C, Tg of 125°C, and water absorption of 0.19%. Genestar G1350A tensile strength is 200MPa. Dry at 70–90°C for 4–8h; moisture content ≤0.20%.
Can PPS Withstand 800V in E-Drive Power Components?
At 800V, electric field strength doubles, making creepage distance and tracking resistance critical. PPS is halogen-free, flame-retardant, and has good tracking resistance. For DURAFIDE 1140A1 (40% GF), nozzle temp is 310–320°C and mold temp is 150°C. Shrinkage is 0.3%/0.8%; uniform mold temperature determines hole positioning. Plastic layer around inserts must be ≥1.5mm, and inserts require preheating.
Why Is the PA46 Processing Window Only 15°C for Under-Hood Structural Parts?
PA46 crystallizes rapidly with high amide bond density; melting point 295°C. Stanyl TS250F6D (30%GF) requires barrel/nozzle temps of 305–320°C. Below 305°C causes short shots; above 320°C causes yellowing/degradation. Residence time >20 minutes also degrades material; purge during downtime. Multi-point temperature differences in hot runner systems must be controlled within a few degrees.
Why Use PEEK for Wear Parts in Transmissions?
Victrex 650G (30%GF): nozzle 395°C, mold 170–200°C, dry at 120–150°C for 3–5h. Shrinkage: 450G 0.most/1.3%, 450GL30 0.30%/0.most. Wear performance depends on mating pair and lubrication. Oil-immersed parts require hot-oil soak validation. Pump part clearance 0.02–0.05mm; uniform mold temperature determines dimensional stability.
Why Are Type-C Housings Both Thin and Aesthetically Demanding?
Type-C shell wall thickness is 0.4mm with high flow ratio. PA9T G1350A (35%GF) with 200MPa tensile strength ensures rigidity. Three cosmetic defects to avoid: weld lines, color variation, flow marks—controlled via mold temp/injection speed, glass fiber dispersion/material temp, and injection speed/gate design. Dry at 70–90°C for 4–8h, moisture ≤0.20%, otherwise silver streaks appear.
Why Must Camera Module Bracket Tolerances Be Tightened to 0.02mm?
0.02mm is one-third of a hair width; step height deviation affects focus. LCP has extremely low water absorption and shrinkage of 0.10%/0.40%. Critical dimension orientation must align with flow direction. Mold machining precision 0.005mm; 3°C mold temp fluctuation causes 0.01mm error. Inspection requires vision systems and constant-temp rooms; acceptance includes positional accuracy after assembly.
Why Must Camera Module Bases Withstand Reflow Soldering?
Lead-free reflow peak temp is 240–260°C. PA9T with 0.19% water absorption risks popcorn effect during soldering. Low-absorption, high-crystallinity PPS does not require prolonged drying. DURAFIDE 1140A1: nozzle 310–320°C, mold 150°C. Low mold temp leads to post-solder crystallization and dimensional change. Hole position tolerance 0.03mm along flow direction; terminal retention force must be retested after soldering.
How Does PA46 Outperform POM for Micro Gears?
POM’s long-term heat limit is 90°C, marginal near motors exceeding 100°C. PA46 has a melting point of 295°C and heat resistance >150°C. Unreinforced PA46 is often used for gears due to toughness; shrinkage ~1.1% requires mold compensation. Critical dimensions: tooth thickness, center distance, end-face runout. Center distance is hardest to control.
Can't find the matching gate issue? Share material, part, and defect details. Our engineers will evaluate it by part.
Online selection and quote