INJECTION MOLDING ENCYCLOPEDIA
Injection Molding Encyclopedia
Find hot runner articles by industry, material, and molding defect.
Frequently Asked Questions
Find products by material
View all four productsTotal 194 articles · Current:All industries
Browse by defect, material, and industry
194 articles
Why Is PA9T Suitable for Automotive Electronics Requiring Reflow Soldering?
PA9T (Genestar G1350A, 35% GF): Melting point 300°C, Tg 125°C, water absorption 0.19%, shrinkage 0.3%/0.9%. At reflow peak temperatures around 260°C, there is sufficient margin but reduced rigidity; real risks are moisture-induced blistering and warpage upon removal. This article details drying conditions, gate types, and three sets of validation data.
Which Factor Keeps PA9T Dimensionally Stable in Industrial Parts After Three Years?
PA9T (Genestar G1350A): Water absorption 0.19%, melting point 300°C, shrinkage 0.3%/0.9%. Dimensional stability comes from low water absorption and high thermal margin. The real challenge for industrial parts is medium compatibility and four-timepoint validation. This article covers gate location, vent depth, and material change cost lists.
Can PA9T Be Used When Sterilization Temp is 134°C but Tg is Only 125°C?
PA9T: Tg 125°C, melting point 300°C, water absorption 0.19%. 121°C sterilization is below Tg, with risks mainly from moisture absorption; 134°C exceeds Tg, where softening and moisture absorption combine to amplify deformation. This article provides four-timepoint validation, alternative material trade-offs, and cleanliness requirements.
How Much Insulation Margin Remains for PA9T on 800V Platforms?
On 800V platforms, electric field strength doubles for the same creepage distance. Tracking risk stems from material tracking resistance, surface cleanliness, and structural distance. PA9T (G1350A): Melting point 300°C, water absorption 0.19%, shrinkage 0.3%/0.9%. This article outlines damp-heat validation sequence, SD Series gate considerations, and flame retardant grade switching notes.
Why Can PPS Replace Small Metal Parts in Automotive Applications?
PPS (DURAFIDE 1140A1, 40% GF): Mold temp 150°C, melt temp max 360°C, nozzle 310–320°C, shrinkage 0.3%/0.8%, pre-dry 140°C×3h. OEM claim: Viscosity does not increase significantly with long residence time, making hot runner use feasible. Real risks are residual stress cracking and brittleness; this article provides medium verification and validation sequence.
How Long Do PPS Parts Last in Industrial Pump Valves?
PPS (DURAFIDE 1140A1, 40% GF): Mold temp 150°C, melt temp max 360°C, shrinkage 0.3%/0.8%, pre-dry 140°C×3h, pinpoint gate φ0.8–1.2mm, vent depth 0.005–0.008mm. For industrial parts, criteria are medium grade, concentration, temperature, contact method, and long-term creep, not just chemical resistance charts.
Does Repeated Steam Sterilization Make PPS Parts Brittle?
PPS (DURAFIDE 1140A1, 40% GF): Mold temp 150°C, max material temp 360°C, nozzle 310–320°C, pre-drying 140°C × 3h or 120°C × 5h, shrinkage 0.3%/0.8%. Single-cycle sterilization at 134°C is safe, but hundreds of cycles risk glass-fiber/resin interface debonding and mechanical property degradation.
Insulation Margins for PPS Parts on 800V Platforms
PPS (DURAFIDE 1140A1, 40% GF): Mold temp 150°C, max material temp 360°C, nozzle 310–320°C, shrinkage 0.3%/0.8%, extremely low moisture absorption. With doubled electric field strength at 800V, margins depend on three factors: creepage distance, material grade tracking data, and surface cleanliness. All three are mandatory.
How Do PEEK Washers in Transmissions Work Without Lubrication?
PEEK (Victrex 650G):: melting point 343°C, nozzle 395°C, barrel rear/mid/front 375/380–385/390°C, mold temp 170–200°C, drying 120–150°C for 3–5 h, barrel capacity 400°C. Wear resistance depends on transfer film formation rather than hardness. Lifespan is determined by the combination of material, counterface, and operating conditions.
Can Low-Warp PA9T Handle Increasingly Fine-Pitch Connectors?
At 0.35mm pitch with ~0.08mm rib width, filling and warpage become critical. PA9T (G1350A) has shrinkage 0.3%/0.9%, moisture absorption 0.19%, Tg 125°C. Achieving low warp requires integrated optimization of material, part geometry, gate design, and mold temperature. This article provides gate designs and three sets of validation data.
Can't find the matching gate issue? Share material, part, and defect details. Our engineers will evaluate it by part.
Online selection and quote