INJECTION MOLDING ENCYCLOPEDIA
Injection Molding Encyclopedia
Find hot runner articles by industry, material, and molding defect.
Frequently Asked Questions
Find products by material
View all four productsTotal 84 articles · Current:All industries
Browse by defect, material, and industry
84 articles
Gate Stringing and Drooling: Why Is It Hard to Adjust?
Stringing and drooling occur when nozzle tip temperature is too high; clogging occurs when it is too low. All three issues happen at the interface between the hot nozzle tip and the mold gate. SD Series seals with a cold slug; VG Series seals with a valve pin; troubleshooting directions differ. LCP window is 335–345°C, PA46 is 305–320°C; materials with narrow processing windows are hardest to adjust.
How Thin Can Walls Be Before Short Shots Occur?
Flow ratio = flow length ÷ wall thickness; halving wall thickness doubles the flow ratio. LCP can fill walls as thin as 0.2mm. For PA9T/PA46, watch out when flow ratio approaches 75 at 0.4mm wall thickness. PPS with 40% GF needs margin. Three conditions for thin-wall molding: high injection speed, mold temp raised 10–20°C, sufficient material temp; mold requires large gates, good venting, and flat ejection.
Why LCP is Preferred for Millimeter-Wave Radar Covers Even at 0.6mm Thickness?
At 76–81GHz, thinner walls reduce loss; LCP's low viscosity allows filling 0.6mm thin walls. With 30% GF, shrinkage is 0.10%/0.40%, with a 4x directional difference; part shape must follow flow direction. Melting point 335°C, low moisture absorption, minimal dimensional shift under thermal cycling. Gates and ejector pins must not fall within the radar main lobe area; coating thickness must be controlled.
Why Use PEEK for Micro Connectors?
PEEK (Victrex 650G): Melting point 343°C, long-term service temp ~250°C depending on grade, nozzle 395°C, mold temp 170–200°C, barrel requires 400°C. Three reasons for using PEEK in micro parts: multiple reflow passes, specific chemical resistance, and long-term exposure above 150°C; the trade-off is cost and yield rate.
Gate Stringing Causes: Gate Temperature, Valve Pin Timing, and Solutions
When the mold opens, a thin, hair-like string pulls from the gate. If left untreated, it causes shorts on adjacent pins, damages mold surfaces, and falling debris contaminates the cavity.
Causes of Excessive Saliva: Film Formation, Dripping, and Sealing from Pack Pressure
When injection ends and the screw retracts, a small film or drip of material escapes through the gate, sticking to the part or dripping onto the mold. This excess material forms a thin sheet that is hard to remove and can damage subsequent parts during molding.
Causes of Nozzle Clogging: Premature Gate Freezing and Carbon Buildup
The previous shot was acceptable, but the next product shows short shots or incomplete filling. Inspection reveals material frozen at a specific hot runner gate, blocking flow. This is most problematic in multi-cavity molds: only one or two of dozens of nozzles clog, making it hard to detect without inspection and resulting in defective batches before discovery.
Gate Carbonization: Black-Brown Layers and Specks
Black specks and inconsistent flow indicate a hard, brittle black-brown layer forming inside the gate. Carbonization accumulates gradually as material coats the gate wall and degrades under repeated heating cycles.
Valve Pin Sticking and Poor Closure: Drive, Timing, and Gate Fit
Two common issues in valve-gate hot runners are: residual material or stringing at specific gates due to poor closure, and delayed actuation causing fill sequence variations or short shots due to sticking.
Hot Runner Leakage: Joint Faces, Preload, and Fit Clearance
Resin rings appear on the mold face, and flash-like overflow consistently occurs at a single location. Inspection confirms leakage from the hot runner/manifold joint or gate bushing interface, not the cavity.
Can't find the matching gate issue? Share material, part, and defect details. Our engineers will evaluate it by part.
Online selection and quote